……And here we go
Re: ……And here we go
That could be an empty box for all we know. If there is a battery in that box, don’t you need a bike to fit it too. Have you found it yet? 
Bit of advice. Buy a good bed and a good pair of shoes, because if you aren't in one you'll be in the other.
Re: ……And here we go
Box is actually empty
BUT, battery is on charge for a first charge when filled
And no, I’ve not found the bike yet. That’s the next task
BUT, battery is on charge for a first charge when filled
And no, I’ve not found the bike yet. That’s the next task
AKA Bald headed b'stard
Re: ……And here we go
Bit of advice. Buy a good bed and a good pair of shoes, because if you aren't in one you'll be in the other.
Re: ……And here we go
Today’s progress, for the doubters out there it’s not AI generated!
AKA Bald headed b'stard
Re: ……And here we go
All I can say is, about bloody time 
Re: ……And here we go
Fuels looking a bit rough…..
But it lives
First start since 2020
https://drive.google.com/file/d/15r8h- ... p=drivesdk
But it lives
First start since 2020
https://drive.google.com/file/d/15r8h- ... p=drivesdk
AKA Bald headed b'stard
Re: ……And here we go
It looks a bit like green pond water. 
Bit of advice. Buy a good bed and a good pair of shoes, because if you aren't in one you'll be in the other.
Re: ……And here we go
It took about 15 seconds on the button but it fired up and sounded great.
I’ve removed the tank, dropped the bowls off and cleaned them out. I’m just waiting for new bowl gaskets to arrive to be able to reassemble
I’ve ordered a clutch slave rebuild kit too as that has leaked. If the kit doesn’t cure it I may have a spare in my box of goodies.
While I’m waiting for parts I’m gunna replace the brake fluid and have the rear tyre replaced. I’ll also drop the oil and change the filter too
Next I need to look for a replacement front tyre next as it’s well out of date and probably has a flat spot after being stood for so long
I’ve removed the tank, dropped the bowls off and cleaned them out. I’m just waiting for new bowl gaskets to arrive to be able to reassemble
I’ve ordered a clutch slave rebuild kit too as that has leaked. If the kit doesn’t cure it I may have a spare in my box of goodies.
While I’m waiting for parts I’m gunna replace the brake fluid and have the rear tyre replaced. I’ll also drop the oil and change the filter too
Next I need to look for a replacement front tyre next as it’s well out of date and probably has a flat spot after being stood for so long
AKA Bald headed b'stard
Re: ……And here we go
Had a busy day working on bike today. Started off by collecting a recently purchased headstock stand from Buxton then had to make a pin as the std fitments made the stand hit the underside of the top cowl. Not good!
So far progress has been good. New rear tyre fitted. Float bowls cleaned, new gaskets and reassembled. No more leaks.
Old fuel drained from tank.
Rear caliper stripped, blasted, repainted, seals removed and grooves cleaned and everything reassembled. Now have a pedal that feels like I’ve dropped an anchor
Clutch slave rebuilt with new seals, bled up and all gears select
Front brakes checked and fluid replaced. However I messed up and broke the lever
while lowering the bike ramp I didn’t realize the lever was catching the end of the lathe causing it to snap at the pivot point. New lever ordered 
Dropped engine oil and filter then couldn’t find the new filter. I therefore had to order one the won’t be here til the end of the week
Finally, I’ve now got headstock stand working right so dropped the front wheel out to get the new front tyre fitted tomorrow
Fingers crossed if all goes well it’ll be ready for the MOT at the start of next week
So far progress has been good. New rear tyre fitted. Float bowls cleaned, new gaskets and reassembled. No more leaks.
Old fuel drained from tank.
Rear caliper stripped, blasted, repainted, seals removed and grooves cleaned and everything reassembled. Now have a pedal that feels like I’ve dropped an anchor
Clutch slave rebuilt with new seals, bled up and all gears select
Front brakes checked and fluid replaced. However I messed up and broke the lever
while lowering the bike ramp I didn’t realize the lever was catching the end of the lathe causing it to snap at the pivot point. New lever ordered 
Dropped engine oil and filter then couldn’t find the new filter. I therefore had to order one the won’t be here til the end of the week
Finally, I’ve now got headstock stand working right so dropped the front wheel out to get the new front tyre fitted tomorrow
Fingers crossed if all goes well it’ll be ready for the MOT at the start of next week
AKA Bald headed b'stard
Who is online
Users browsing this forum: No registered users and 1 guest