No Fuel Pump or Exup Servo ???

Post by **Stig** » Sat Dec 30, 2017 6:58 pm

Is there an alarm or immobiliser fitted?

matzxr · Post by **matzxr** » Sat Dec 30, 2017 9:07 pm

No alarm or immobiliser

Teego · Post by **Teego** » Sat Dec 30, 2017 9:40 pm

OK, so the servo and fuel pump should start with the ignition on, the kill switch set to run and the gears in neutral. Your problem suggests it's not a servo or pump problem but something upstream that is common to both.
On these settings you should also see the oil level light come on when you press the starter. Does this happen?
Does the starter engage and turn the engine?
Do lights,indicators etc work as they should?
What is the condition of the battery?
If we can work our way thru this we should find the problem.

matzxr · Post by **matzxr** » Sat Dec 30, 2017 9:58 pm

I have no Clocks connected as yet.
Starter Motor spins engine over ok, was using jump leads.

Will be fitting the clocks tomorrow (sunday) so can check on the oil light.

Post by **Stig** » Sun Dec 31, 2017 5:22 pm

Don't know about the easyouts. Logic suggests forcing a taper into a fixed hole the expand something that's already stuck tight isn't a way to go

I find a sharp tap with a hammer to jolt the bond usually let's it move, but that's only if there's enough key to get it to grip

matzxr · Post by **matzxr** » Sun Dec 31, 2017 7:45 pm

As in, knocking it undone ??
Too narrow down there for that.

Post by **Stig** » Sun Dec 31, 2017 7:57 pm

I have a mini impact driver made by Lazer tools. Gets into most places with the right bit fitted

matzxr · Post by **matzxr** » Mon Jan 01, 2018 12:39 pm

Had to bloody drill the Mixture Screws out

Does anyone know the Thread Size please ?

EXUP FREAK · Post by **EXUP FREAK** » Wed Jan 03, 2018 8:22 pm

The pump and servo are run off the indicator circuit start thare

matzxr · Post by **matzxr** » Sat Jan 06, 2018 12:38 pm

Ok, update;
No headlights, or oil light when pressing starter ?

Post by **nuggitt** » Sat Jan 06, 2018 1:15 pm

Its just a thought. Have you looked in the handlebar switch? Could be something loose or coroded in there.

matzxr · Post by **matzxr** » Sun Jan 07, 2018 5:57 pm

Another update;
Still no joy here.

I have lights now, high & low beam, horn.

No indicators, fuel pump or exup servo, also, no spark.

Swapped another CDI, Coils, re-connected every connector, checked fuses again - all ok, swapped indicator relay

Petrol + match is now high on the agenda

Post by **Stig** » Sun Jan 07, 2018 6:11 pm

Exup servo doesn't move when powered. You have to rotate the servo pulley with ignition off. It will reset to centre if it's working correctly

Does the starter turn? Try bridging the relay contacts with a screwdriver to see if starter spins over

Is there power out the back of the fuse box to the indicator switch and does it reach the switch?

matzxr · Post by **matzxr** » Sun Jan 07, 2018 6:30 pm

No exup servo (I do check by rotating it)
Starter Motor works ok.

Post by **nuggitt** » Mon Jan 08, 2018 11:37 am

matzxr wrote:Another update;

I have lights now, high & low beam, horn.

I'm just back tracking a bit here. What did you do to get the lights and horn working?